Product Center
Professional floor paint manufacturers
Color sand self-leveling
Key Word:
Category:
Description
Product Description:By the epoxy resin and curing agent, color floating sand composed of three components of non solvent type floating sand self leveling floor coating
Product use:Color sand sense self-leveling effect, used for decorative and abrasion resistance requirements of the commercial places of the ground coating;
Performance characteristics:1. Solvent-free, environment-friendly;
2, excellent leveling; rich color, very good decorative effect;
3. Good hardness, good wear resistance and scratch resistance;
4. Good yellowing resistance and chemical resistance;
Construction method: With trowel construction, according to the amount to choose the tooth length, after construction need to use defoaming drum defoaming, regular choose 3mm tooth knife trowel scraping
UseQuantity:2.5 ㎏/m2 ~ 3.0 ㎏/m2
Note: According to the choice of floating sand thickness different dosage (please consult the company's technical personnel for details).
StorageDepositSex:Effective storage period of one year, after expiration can be inspected according to quality standards, such as compliance with the requirements can be used.
Technical indicators:
| Project |
Reference Indicators |
Test standard and description |
| Proportion (weight ratio) |
A:B：C=6:1:1.2 |
three components |
| usable time |
15 minutes |
25 ℃ (the higher the temperature, the shorter the usable time) |
| Diluent |
Do not recommend add |
|
| Table dry (h) |
2 to 3 |
25℃ |
| Gel time (min) |
35 |
|
| Practical work (d) |
2 to 3 |
|
| Adhesion (grade) |
≤1 |
GB/T22374-2008 |
| Pencil hardness |
≥ 3H |
GB/T22374-2008 |
| Compressive strength (MPa) |
≥ 45 |
GB/T22374-2008 |
| Abrasion resistance (750g/500r,g) |
≤ 0.030 |
GB/T22374-2008 |
| Alkali resistance (20% NaOH,72h) |
No blistering, no peeling, slight discoloration allowed |
GB/T22374-2008 |
| Acid resistance (10% H2SO4,48h) |
||
| Oil resistance (72h) |
||
Product use instructions
lConstruction shall be carried out under the conditions of temperature 5~35 ℃ and relative humidity ≤ 85%. Before coating and during curing (before surface drying), the surface temperature of the base surface should be higher than the dew point by more than 3 ℃ to prevent water vapor condensation on the surface of the substrate and wet film from affecting the coating adhesion and surface effect;
lThe coating is on a clean, dry, flat and pore-free intermediate coating. If there are pits on the base surface, epoxy intermediate coating shall be used to make up for the surface uniformity;
lThe product has been proved by experiments to have sufficient construction adaptability, should not add any solvent and diluent, if you want to add please consult our technical department.
lBefore construction, the component is fully stirred evenly, and the B component is mixed according to the weight ratio. Depending on the ambient temperature, the summer is fully stirred for 2~3 minutes, and the winter is fully stirred for 3~5 minutes. After AB is mixed, the tooth knife trowel is used to scrape. At the same time, the defoaming roller is used to help the material defoaming;
lDuring the construction of floating sand self-leveling, it is necessary to confirm that the color of the middle coating is similar to or consistent with the color of the topcoat. If FS01 color and other light colors are selected, it is recommended to use EC25 color middle coating or surface coating for backing to prevent the surface color of colored sand self-leveling from being inconsistent due to uneven construction dosage.
lBefore large-scale construction, please check the model and color of the materials, and make 5-10 square meters of small samples to confirm that the effect meets the quality requirements before large-scale construction;
lWhen the temperature is high, pay attention to the fast reaction gel and shorten the use time. Please determine the amount of ingredients for each time according to the actual use temperature and construction progress. The prepared materials must be used up at one time, and the remaining components A, B and C must be sealed and preserved;
lThe edge of the construction wall should be as uniform as possible to avoid defects caused by backflow;
lEpoxy resin floor coating in the construction of the completion of the curing period of about 7 days (25 ℃), the first three days of the coating as the main curing period, clear completely closed workplaces, curing period to prohibit water and heavy pressure, so as not to artificially damage the epoxy coating;
lStorage conditions: should be sealed in a cool and dry place, storage temperature 10~35 ℃; less than 10 ℃ storage conditions, paint components may occur crystallization state, available water bath heating method heating 3-5 hours to remove the crystallization state, does not affect the curing effect, but the surface coating needs to use 120 mesh filter after use.
lDuring transportation, ensure that the carriage environment is dry and closed, and the material code is laid flat and stable.
lDuring construction, please keep the site well ventilated and no smoking. Please wear protective clothing, gas mask and protective gloves during construction to avoid inhalation of paint mist and skin contact with paint. Paint spilled on the skin should be cleaned immediately with a suitable detergent. If splashed into eyes, rinse immediately with plenty of water and seek medical attention immediately.
lThis product is a combustible article, storage, transportation, construction must be away from the source of fire and maintain good ventilation; in the event of a fire, use a dry powder fire extinguisher or sand cover to extinguish the fire;
Get A Quote
Note: Please leave your email address, our professionals will contact you as soon as possible!
Guangzhou Zeal Chemical Co., LTD
Address: 4F, Corey Building, 336 Qingxin Road, Guangzhou Economic and Technological Development Zone
Telephone：+86 020-8205 7070
Mailbox：info@gzzeal.com
Pt.Fika Makmur Indonesia
JALAN PETA BARAT JL. Peta Barat No.23,Jurumudi, Kec. Benda, Kota Tangerang, Banten 15124
Telp:+62 21 3826 9138